Ten Steps to Wallpapering

Wallpapering isn’t just for the 1980s, there are lots of modern-day designs that make it a surprisingly stylish alternative for embellishing. It’s also a DIY task that when performed properly, can be actually fulfilling. Here are 10 actions to wallpapering, with some top ideas for the challenging bits

Preparing the walls

Preparation is the first step in basically any DIY job, but for wallpapering, it is essential. Examine the walls for any nails or old wall plugs. Nails can be easily eliminated with a claw hammer, however ingrained wall plugs can be difficult to remove. If you can’t get them out with pliers or wire cutters. Attempt screwing in any old screw that fits, and utilise the claw hammer on the screw, this ought to highlight both the screw and the wall plug. This could easily bring part of the plaster with it, which can be repaired using multi-purpose filler and a scraper, and when dry you can level off any bumps with sandpaper. Lastly, make sure the walls are totally tidy and dry.

Ensuring the first strip is level

Using a chalk line, plumb or level, draw a vertical line on the wall. This will help ensure that when you apply the first strip it is level, this is especially crucial if you live in an older home where the walls and joins aren’t ideal. When you’ve done this you can measure out the very first strip, ensuring that there suffices excess paper for overlap– don’t try to cut to size.

Prepare the paste and paper

Using a paint kettle or roller paint pail, blend the wallpaper adhesive with the required amount of water as shown on the pack. Using a wallpaper table, roll the paper out weighting the ends if needed. The tip for getting ideal protection of paste is to utilise a high quality 1/2 inch roller– cheap ones will leave fuzz behind. Transfer the wallpaper adhesive to the roller tray and use a thin coat to the paper ensuring you reach the corners. Some find it simpler to rather apply the paste directly to the wall.

Applying the very first strip

Using the line you’ve drawn, hang the first strip from the top. using a wall paper brush gently smooth out from the middle of the paper to the edges.

Getting Rid of Air bubbles

Using the wall paper brush should guarantee you’ve removed any bubbles, however if there are any left usage a clean cloth to smooth them out. Work them out to the edges. If you’re getting a great deal of bubbles or one big one, carefully lift the paper and again, start smoothing it out to the edge.

Cutting the excess

Once you have the paper entirely flush to the wall, skirting boards and coving, you are ready to cut any excess. Use a Stanley knife to thoroughly follow the line of the boards and coving. If you discover this tough, pull the wallpaper away slightly and cut using wallpaper scissors. You could also use a taping knife as a cutting edge guide.

Matching the pattern

Following action 4, prepare the paper, once again making sure there’s enough excess for cutting. It’s easiest to fold or roll the paper and after that work to match up the pattern. Guarantee there is no overlap with the first strip, they should sit flush to each other so there’s no bump on the sign up with.

Corners

Using wallpaper to corners can be tricky, but it can be done if you take your time. Apply to the first wall and then using the brush or fabric, gently work the paper into the corner, up until the paper gently rests on the second wall. Keep your motions light so that you have enough motion in the paper to solve into the corner. Using scissors, make a cut in the paper on top where the corner satisfies the ceiling, so that you can fold the paper over to the second wall. Do this again at the bottom.

Cutting around sockets

When you reach an area which contains a socket or light switch, hang your wallpaper as before however don’t smooth down the strip too much around the area. Where you feel the socket, make a cut around the middle. Cut away in a diamond reaching each corner, be very cautious not to cut too much. Smooth down the paper to the edges of the socket and utilise the Stanley knife to take the paper to the corners. As soon as you are pleased that the paper is smooth around all edges, utilise the knife to cut the paper flush to the socket. Additionally, slightly loosen the screws on the socket/switch so there is a small space to the wall and cut the paper so it can be tucked into the gap and behind.

Completing

To end up the job, smooth down every piece with a natural sponge or tidy cloth, and use the joint roller to roll once again over every seam– this helps set the edges, however do not roll too tough as adhesive may squeeze out. Rolling is essential to assist keep the edges from curling.

Post Sponsored by Manchester Emergency Glazier.

Leave a Reply

Your email address will not be published. Required fields are marked *